USR2249 22 Mbps Wireless Access Point

(USR812249, USR842249)

USR2249

Warranty: 2 Year

FAQs

  • Repair Information
  • What are the different modes for the Wireless Access Point?
  • My computer can not communicate with other computers
  • Low Link Quality
  • Communicating with your Access Point
  • Wireless range performance
  • How do I enter a 256-bit WEP Key in Windows XP?
  • How do I enable the USRobotics Wireless Configuration Utility in Windows XP?

    • Additional Support

    If the support information in this section doesn't help you solve your issue, you can contact a USRobotics Help Desk Technician directly.

    		Note: In order to prevent your browser from trying to open these files, right-click the file and select Save Target As... to download.

    Manuals and other Documents

    Driver installers and Firmware

    54 Mbps Performance Upgrade
    Note:  To take full advantage of the 54 Mbps Performance Enhancement (EMEA, ME, Czech) you must completely update your wireless infrastructure. It is recommended that you use the current utility to update the firmware. Once the firmware is updated, then update to the new utility. To do so, follow the procedures below in the order in which they appear.

    Configuration Utility Update- Version USR04_1.0a

    Note:  It is critical that you update the AP Utility on all computers that it is running on. Using the new AP firmware with the old utility will NOT work properly.

    If the AP utility has never been installed:

    1. Print these instructions.
    2. Download the USR04_1.0a_APUtility.exe file located at the bottom of the page.
    3. Double-click the USR04_1.0a_APUtility.exe file to start the installation process.
    4. Follow the prompts to complete the installation.

    If you are upgrading your AP Utility:

    1. Print these instructions.
    2. Download the USR04_1.0a_APUtility.exe file located at the bottom of the page.
    3. Run the USR04_1.0a_APUtility.exe file and it will detect the previous version of the AP Utility.
    4. It will prompt you to uninstall the old version.
    5. Click Yes and complete the uninstallation process.
    6. Once it is uninstalled, you will be prompted to install the new version.
    7. Follow the prompts to complete the installation.
    USR04_1.0a_APUtility.exe 2.04 MB 28-03-03
    22 Mbps Wireless Access Point Firmware Update

    Note: It is critical that the AP is assigned an IP Address before you try to update the software and firmware. Since the update process uses TFTP, a valid network IP Address will be required. A static IP address is NOT required, but the device should have at least attained a DHCP address. If you load the new utility without updating the firmware, you may be prompted to update the firmware. However, should this occur, you must have a working and valid IP address on the AP. If you load the new firmware without updating the utility, you will not be able to access the AP.

    1. Print these instructions.
    2. Download the USR_ap_50g_nml.bin file located at the bottom of the page.
    3. It is strongly recommended that you write down your settings for your device before upgrading. Once the upgrade is complete, the device will be set to manufacturers default.
    4. If you have updated the AP Utility and scanned your network for available APs, you may be prompted to update your AP if the new utility detects old firmware. If so, select Browse to locate the latest firmware file and update accordingly.
    5. If you are using the old version of the AP Utility, Log into the AP, select the Tools page, and select Browse to locate the new firmware file, USR_ap_50g_nml.bin. Once located, click Update.
    usr_ap_50g_nml.bin 960 KB 21-03-03
    For all archived files please visit ftp.usr.com/usr/22xx

    Tech Support via E-mail E-mail a USRobotics Support Technician.

    Product Registration Activate your USRobotics product warranty online.